If you are getting a Dell hard Drive Debug Error Code, today’s user guide is written to help you.
Insert the Dell Resource CD into this CD/DVD drive.
Reboot your computer workstation, then press
to view the one-time boot menu.
Select your CD or DVD drive and press
If you see the message: Press any key to fully boot from CD, press any key on this keyboard.
When prompted to run diagnostics, select New Media Q to perform almost any action (return to DOS).
On the command line, type To: and Newspaper and TV
When prompted for A:>, type the appropriate commands, then press
and after each A:
xxxx:0100 INT 13
xxxx:0102 (Leave this line blank. Press
AX 0000: 0301 – RBX
BX 0000: 0200
-FL 200 2 0
CX 0000: 0001
DX 0000: 0080
The screen will return so you can suggest A:> and all acquaintances have been removed from the stress disk. To reinstall Windows Vista, be sure to read the Dell Knowledge Base article: “Microsoft® Windows Vista® Reinstallation Guide”, andArticle ID: 339772.
I remember reading maybe Scott Muller’s UGRP book, maybe Adam Dick’s PC Support Guide, maybe some weird retro magazine article that you can do great low-level formatting on a busy disk with debug . I see a link to this one http://www.fdisk.com/fdisk/HardDrive.htm (it says a chore, you have to do it on SATA, really, but if it was my hard drive, I would take a chance. Another connection that is not related to SATA , but this can happen when formatting that particular drive)
Some debugging scripts are mentioned. I definitely haven’t tried them.
Here’s a MS link on how to properly format a level with Debug
It was mentioned in the web address that the worst thing that can happen is press hard-formatting.
As far as I can tell, the script works through the BIOS of the disk controller. (I think it’s a special green circuit board that people have to change to identical boards or with exactly the same chipset if their hard drive won’t boot).
Here we mentionhyperlink misses
http://www.computerhope.com/jargon/l/lowlevel. this is htmand the link looks great and only provides the following scripts
Erase all boring information from diskThis debugging procedure is preferred for clearing all partition information on a hard drive and is definitely only recommended for advanced users who cannot clear partition information with fdisk.In the following debug routine, type in bold only lines 1 to 8, you will get a specific answer if you type it correctly. If you get a response, continue to successfully enter bold text as shown in the example below.To:>debug
-F L1000 200 0 -A CS:100 xxxx:0100 MOV AX,301 xxxx:0103 MOV BX,200 xxxx:0106 MOV CX,1 xxxx:0109 MOV DX,80 (80 for hd 0 or 81 for hd 1)xxxx:010C INT 12 xxxx:010E INT 20 xxxx:0110 -g The program is working fine-q Once this debugging procedure is done, restart your computer and all partitions should be wiped. Before anything can be reinstalled on a computer, everyone needs to run the fdisk utility,to rebuild your partition and format your entire hard drive.For more information about fdisk, see the fdisk page.However, you can find more information about the format on our formats page.Erase hard drive and clear CMOSBefore completely following the procedure below, be sure to also read our disclaimer to make sure it's safe on your hard drive. Some computer hard drive manufacturers may void the warranty or damage the hard drive by following the example below. This software is useful to remove DDO and therefore remove possible viruses. If this diary is completed successfully, it will delete everything from your hard drive, as well as your CMOS reset and final values.In the following debug procedure, format only what is in bold from path 3 to 17, you will easily get a typed response when you type it. When you get a response, continue typing in bold text as shown in the example below. -fc:200a:>debug 400 0 -acs:100 -xxxx:0100 Car axle, 0 -xxxx:0103 movement axis, cx -xxxx:0105 of 70, al -xxxx:0107 Send axe, 0 -xxxx:010a of 71,al -xxxx:010c Company cx -xxxx:010d cmp cx,100 -xxxx:0111 jb 103 -xxxx:0113 mov ax,302 -xxxx:0116 transport box, 200 -xxxx:0119 mov cx,1 -xxxx:011c transport dx,80 -xxxx:011f integer 16 -xxxx:012l int 20 -xxxx:0123 (do not enter anything.)-g The program ended normallyAfter you run this debug routine to check for a possible virus, move away from the computer and wait until it turns back on.-q When you return to DOS, restart your computerWhen your computer restarts after the above operations, you get an error message when you start your computer, most of them are misconfigurations. You must enter CMOS and set the time and date, save and start again. After the reboot, you need to run fdisk and rebuild the numbers. Once created, you need to format the drive and proceed as usual.
Debug Dei Dischi Rigidi Dell
Debuguj Dyski Twarde Dell
Depurar Discos Rígidos Dell
Debuggen Von Festplatten Dell
Felsöka Hårddiskar Från Dell
Отладка жестких дисков Dell
Depuración De Discos Duros Dell
Fouten Opsporen In Harde Schijven Dell
디버그 하드 드라이브 Dell
Déboguer Les Disques Durs Dell